...SKU: ETS_Quiet_Exhaust The ETS Quiet V2 Exhaust system is a direct replacement of the factory cat back. This exhaust system features a large muffler similar to stock which results in a quiet exhaust system without the added back pressure from...
...ETS_EVOX_V2 The ETS Exhaust system is made right here at our facility! The exhaust system features a 3.0" mid pipe that tucks up tightly against the underside of the vehicle giving you more ground clearance then any other exhaust on the market....
...ETS-EVO-X-Turbo-Back-Exhaust This is a full turbo back exhaust. This Exhaust Includes: ETS Downpipe: The ETS Evolution X O2 Eliminator Downpipe is a direct replacement for the stock O2 Housing and Downpipe. This downpipe features a recirculated...
...ETS Mitsubishi Evolution X Upper Pipe removes the restrictive factory pipe which necks down to 1.75" before the turbo outlet and replaces it with a full 2.5" upper intercooler pipe which helps with throttle response as well as reliability. The...
...ETS_EVOX_PipingKit Weight: 25.00 lbs The ETS EVO X intercooler piping kit is next in line and is a very cool modular package. The upper intercooler piping starts with a smooth mandrel bent 2.5" stock turbo outlet pipe which connects to the...
...ETS_EVOX_PipingKit Weight: 25.00 lbs The ETS EVO X intercooler piping kit is next in line and is a very cool modular package. The upper intercooler piping starts with a smooth mandrel bent 2.5" stock turbo outlet pipe which connects to the...
...ETS_EvoX_Extreme The ETS Mitsubishi Evo X V2 Extreme Exhaust System is a direct replacement of the factory cat back exhaust system. This exhaust was designed for the true enthusiast looking for maximum performance with no mufflers or restrictions...
...ETS_EVOX_T3_TK Weight 70.00 lbs For serious power upgrades on the Evo 10 look no further than an ETS Turbo Kit. Packed with features like high flowing Equal Length ETS Manifold, true Merge Collector, full 3” Downpipe, direct routed Wastegate...
...ETS_EVOX_INT The ETS MAF Intake Includes a huge 5" inlet K+N air filter which feeds the intake pipe via the ETS EVO X MAF adapter which is milled on the ETS lathe for the perfect transition to the inlet diameter of the MAF sensor tube. With a...
...ETS_EVOX_DP_Recirc Weight: 16.00 lbs The ETS Evolution X Recirculated O2 Eliminator Downpipe is a direct replacement for the stock O2 Housing and Downpipe. This downpipe features a recirculated wastegate dump for stock like sound under wide open...
...ETS_EVOX_TI_UICP The all new ETS Titanium Series upper intercooler pipe. This pipe is designed for maximum durability and performance by eliminating many of the unnecessary bends in the stock piping that snake around the stock engine bay. The...
...ETS_EVOX_UICP The upper intercooler piping starts with a smooth mandrel bent 2.5" stock turbo outlet pipe which connects to the remainder of the hot side piping. The stock turbo outlet pipe is separate to allow it to be swapped out with the...
...ETS_EVOX_LICP Weight: 10.00 lbs The ETS Mitsubishi Evo X Lower Piping Kit removes the factory rubber hoses which are prone to ballooning and popping off under higher boost pressure. From the intercooler outlet the 2.5" mandrel bent piping...
...ETS_EVOX_T4_TS_TK Weight: 70.00 lbs For serious power upgrades on the Evo 10 look no further than an ETS Turbo Kit. Packed with features like high flowing Equal Length ETS Manifold, true Merge Collector, full 3” Downpipe, direct routed Wastegate...
...you're looking for quicker acceleration, a lightened flywheel is a necessity for overall engine performance gain! Tomioka Racing Light-weight Flywheels bring the best of factory-weight flywheel and the ultra light weight flywheel for well balanced...
...ETS Mitsubishi Evolution X 3.5" Maf Housing with Velocity Stack. Made to replace your stock housing to allow more air flow for your high horsepower Evo X. Made with a 5" wide velocity stack to allow the use of a larger filter for maximum air flow....
...Fab EVO X 4B11 Aluminum Torque Plate Part # EVOX-TQPLATE-00 Fits: EVO X Anytime you're boring a block distortion will occur to the cylinders unless you have a honing/torque plate installed as a brace. Our plate is CNC machined from 2" thick...